Maximo Accoya: Measure Your Project and Order the Right Quantity

Understanding Maximo Accoya Product Dimensions

Maximo Accoya is available in various profiles suitable for decking, siding, ceilings, windows, doors, trim, and molding. While specific dimensions can vary by profile and application, understanding the fundamental units is key. Maximo Accoya is typically supplied in linear feet or board feet, depending on the profile and its intended use. For siding and decking, planks usually come in standard lengths, which will influence how you plan your cuts and minimize waste.

It is essential to review the specific product catalog or speak with a Lumber Plus representative to confirm the exact dimensions, available lengths, and coverage area per unit for the Maximo Accoya profile you intend to use. This information forms the basis of your quantity calculation.

Accurately Measuring Your Project Area

The first step in calculating material needs is to precisely measure the area where Maximo Accoya will be installed. For walls or facades, measure the height and width of each section to determine the total square footage. For decking, measure the length and width of the deck surface. Always measure twice to ensure accuracy.

When dealing with irregular shapes, break the area down into simpler geometric forms (rectangles, squares, triangles) and calculate each section's area separately before summing them up. Remember to account for any openings, such as windows or doors, if the Maximo Accoya is being used as cladding, as these areas will not require material. However, often a portion of the material around these openings will still be used for trim or framing.

Planning for Cuts and Layout

Maximo Accoya, like any wood product, will require cuts to fit your specific project dimensions, especially around corners, openings, and at the ends of runs. Planning your layout in advance can significantly reduce waste.

Consider whether you will be installing the material horizontally, vertically, or in a more complex pattern. For horizontal siding, you might aim for longer continuous runs, while vertical applications might involve more pieces cut to specific wall heights. Sketching out your layout on paper or using design software can help visualize where cuts will occur and how to optimize board lengths.

Incorporating a Waste Factor

Even with careful planning, some material waste is inevitable due to cuts, minor installation errors, or unforeseen damage. A waste factor is an additional percentage of material added to your base calculation to account for this. The typical waste factor for wood products ranges from 5% to 15%, but this can vary based on project complexity, installer experience, and the specific Maximo Accoya profile.

For projects with many cuts, intricate patterns, or those requiring precise alignment, a higher waste factor (e.g., 10-15%) might be prudent. For simpler, straightforward installations with long runs, a lower percentage (e.g., 5-7%) may suffice. It's always better to slightly overestimate than to run short and delay your project waiting for a supplementary order.

Worked Example: Calculating Maximo Accoya Siding for a Wall

Let's consider a hypothetical wall section to be clad with Maximo Accoya siding. Assume the wall measures 12 feet high by 20 feet wide. There is one window opening measuring 3 feet high by 4 feet wide.

1. **Calculate Total Wall Area:** 12 ft (height) x 20 ft (width) = 240 sq ft.

2. **Calculate Window Area:** 3 ft (height) x 4 ft (width) = 12 sq ft.

3. **Calculate Net Area to Cover:** 240 sq ft - 12 sq ft = 228 sq ft.

Now, assume the specific Maximo Accoya siding profile you've chosen has an effective coverage of 5.5 inches per plank (after accounting for overlap or shadow line) and is available in 16-foot lengths. To convert the effective coverage to feet: 5.5 inches / 12 inches/foot = 0.4583 feet.

4. **Calculate Coverage per 16-foot plank:** 0.4583 ft (width) x 16 ft (length) = 7.33 sq ft per plank.

5. **Calculate Raw Number of Planks Needed:** 228 sq ft / 7.33 sq ft/plank 31.1 planks. Always round up to the nearest whole plank, so 32 planks.

6. **Apply Waste Factor:** For this project, we'll use a 10% waste factor due to the window cuts and potential end-cuts. 32 planks * 1.10 = 35.2 planks. Round up to 36 planks.

Therefore, for this hypothetical wall section, you would plan to order 36 Maximo Accoya planks of the specified profile and length. This calculation provides a starting point; always confirm actual material yield and waste assumptions with your installer or supplier based on the exact profile and installation method.

Before you order

• Have you measured all project dimensions accurately?
• Have you calculated the net area to be covered, accounting for openings?
• Do you know the exact effective coverage of your chosen Maximo Accoya profile?
• Have you considered your installation pattern (horizontal, vertical, diagonal)?
• Have you applied an appropriate waste factor (e.g., 5-15%) for your project's complexity?
• Have you confirmed available Maximo Accoya lengths and profiles with Lumber Plus?
• Have you accounted for any trim or accessory pieces needed around openings or corners?
• Do you have a plan for managing potential offcuts and minimizing waste?

Confirm installation details, approved uses and warranty terms in the current instructions for the exact product and profile. Your installer should verify the substrate, structure and applicable project requirements.

Questions to help you decide

Keep planning your project